Dodge Check Engine Light

Dodge Check Engine Light

A flashing light indicates that the problem is tremendously serious and if not taken care of quickly may result in major and serious damage to the car. If the check engine light in your Dodge starts flashing, that means that the problem needs attention quickly and your Dodge should be brought in immediately. This blinking light ordinarily signifies a severe engine misfire allowing unburned fuel to be dumped into the exhaust system. There it can quickly raise the temperature of the catalytic converter to a point where damage is likely, requiring an pricey and extensive repair. Some owners ask if spark plugs cause the check engine light to flash? This can specifically be the cause. A broken, old or dirty spark plug can cause the engine to misfire. If the problem is entirely ignored or you continue to drive, this can spread to the spark plug wires, catalytic converter, or ignition coils which can lead to a extremely expensive repair. If your check engine light is regularly flashing, please contact our team of automotive experts at Larry H. Miller Chrysler Jeep Dodge Ram Bountiful immediately by calling 3854855488.

What could cause the check engine light to come on in a Dodge?

When your check engine light comes on, this could be as simple as tightening or replacing your gas cap. Still, the check engine light could also be a warning of a significant problem that could cause serious damage to your engine and come with a hefty and costly repair bill. Depending on your make and model, the check engine light will illuminate or blink. A steady and continuous glow typically means something less serious but a flashing check engine light indicates that your vehicle’s engine is in significant trouble and useful service is needed rapidly. If your check engine light is flashing in your Dodge, we tremendously advocate not to drive the vehicle and schedule Dodge service today. Below is a list of the most common reasons your check engine light can come on:

• New Spark Plugs or Plug Wires are required for your Dodge. The spark plugs are the part of your engine that ignites the air/fuel combination in the combustion chamber of your vehicle. This explosion is what moves the pistons and makes the engine run smooth. The spark plug wires deliver the spark from the ignition coil to the spark plugs. If your spark plugs or spark plug wires are bad or old, you will experience a conspicuous poor performance and decreased power. In some extreme cases, your engine will have trouble starting or continuing to run. Worn spark plugs and plug wires can cause clogged catalytic converter or damage to ignition coils and O2 sensors, leading to more expensive repairs.
• Your catalytic converter is bad or going bad. The catalytic converter is a part of your Dodge ’s exhaust system. The catalytic converter's function is to turn the carbon monoxide created by the combustion process into carbon dioxide. A broken catalytic converter is usually caused by repeatedly neglected maintenance, which is why Larry H. Miller Chrysler Jeep Dodge Ram Bountiful offers a free multi-point examination with every Dodge service. If you have an issue with your catalytic converter and don't get it repaired, your Dodge will not pass an emissions test, show a lack of engine performance and will negatively affect your fuel economy. Your car may run at a higher temperature, too, which can cause other perilous problems from overheating.
• Your O2 Sensor (Oxygen Sensor) needs to be replaced. The Oxygen sensor, known as the O2 sensor, measures the amount of oxygen in your exhaust system. If there is excess oxygen in your exhaust system, fuel burns more swiftly and your vehicle will be less efficient when it comes to fuel economy. So what happens if I don’t replace your O2 sensor? A damaged sensor can not only affect your miles per gallon, but it can cause meaningful damage to your catalytic converter and your Dodge 's spark plugs. The O2 sensor sends data to the vehicle’s onboard computer to determine the exactly correct combination of air and fuel that enters the cylinders in your engine. A damaged O2 sensor can still cause a car to fail an emissions test.
• Issues with any aftermarket items. An aftermarket alarm, exhaust or other item can wreak extreme havoc on your Dodge if it’s not installed perfectly. These aftermarket parts and accessories can drain the battery, trigger the check engine light, or even prevent the vehicle from starting. If these issues sound familiar, bring your to Dodge and have our team of talented certified mechanics guarantee that your aftermarket items were installed accurately and aren't causing any issue. Getting accessories, especially aftermarket parts and accessories, or using OEM parts first place might cost a little bit more but could help you save substantially from having to get poor work and damage caused by poor installation work corrected.
• Your mass airflow sensor (known as MAF) needs to be replaced. The mass airflow sensor in your Dodge is what determines how much fuel is required to run your engine efficiently by measuring the amount of air entering the engine. As a part of the engine management system, the mass airflow sensor helps adjust to certain changes, like altitude. If your Dodge is having trouble starting, idling rough or has a sudden fast change in the position of the throttle pedal, this could be a vital sign of a damaged mass airflow sensor.
• One of the most common and frequent cause is that your Dodge gas cap is loose, broken or missing. The gas cap for your Dodge serves numerous purposes. It prevents perilous gas fumes from being released when you aren't driving, it seals the fuel system and helps maintain pressure within the fuel tank. What happens if you have a damaged fuel cap? If your gas cap is old or has a ruptured seal, you can lose fuel through evaporation which will result in more trips to the pump and be more expensive. Luckily, to replace a gas cap isn't expensive. If your check engine light turns on rapidly after you put gas in your Dodge, first thing you should check is to make sure the cap isn’t loose — or that it's still on your car’s roof or at the fuel pump.
• Your Dodge has a vacuum leak. Every Dodge has a vacuum system that performs a wide variety of functions. The vacuum system still helps lower harmful emissions by routing the fumes as gasoline evaporates through the engine. If you notice that your RPM is high in idle or randomly surges, a vacuum leak could be the cause. Over time, vacuum hoses can dry out and crack, especially if they’re exposed to intense heat or extreme cold.
• The battery is low or dead. The battery in your Dodge is every critical. Without a car battery, your car won’t start, light up the road ahead, play the radio or charge your phone. Today’s car batteries last much longer than they did a few decades ago, and they don't really require maintenance. The price of a new one depends on the type of Dodge you drive, but check our current service coupons and specials.

What Does the Check Engine Light Mean?

One of the most commonly misunderstood lights or indicators in your Dodge is the check engine light. The check engine light is part of the essential onboard diagnostics system, and displays in a variety of different ways. It can say "Check Engine", it can be a symbol of an engine, it can even be a combination of both. This light illuminates in either an amber or red color and is part of the diagnostics system found on your car. Onboard computers increasingly have controlled and monitored car performance since the 80s and do a variety of things for your Dodge. Some of these essential duties include controlling engine speed, shifting automatic transmissions ignition timing, and implementing security control, just to name a few. With that being said, the check engine light can mean an assortment of different things. It can be as simple as your gas cap being loose or as perilous as engine knocking. If your check engine light is on in your Dodge, contact Larry H. Miller Chrysler Jeep Dodge Ram Bountiful. Our Dodge service department can help you find out what code is turning your check engine light on or diagnose why your check engine light is flashing. Contact Larry H. Miller Chrysler Jeep Dodge Ram Bountiful today!

Dodge Check Engine Light Codes

The check engine light turning on can be quite intimidating, exceptionally to see that little light on your vehicle’s dashboard suddenly illuminate, but in reality, it is not something that should cause you to shut down in fear right away. If you hear the term, diagnostic trouble codes (DTC), these are just another name for check engine light codes. These are automotive computer codes stored by the ECM, again known as the OBD (on-board computer diagnostic system) in your. There are hundreds of different codes that your check engine light can accurately represent. While that sounds daunting, with a little patience, tackling basic diagnostics will give you helpful knowledge about your car and will again allow that critical Check Engine Light to do what it is absolutely supposed to do: be your guide. Unfortunately, clear and useful car symptoms do not repeatedly accompany an illuminated Check Engine Light. Since there are hundreds of likely OBD codes, there are again hundreds of likely reasons for the light, including:

• Old Battery
• O2 Sensor
• Ignition system faults
• Computer output circuit issues
• Fuel and air metering systems problems
• Bad Spark Plugs
• Transmission issues
• Loose Gas Cap or Missing Gas Cap
• Emissions controls issues

This is why it is vital for someone who does not have a lot of predominant automotive knowledge to not assume what a code means. Call Larry H. Miller Chrysler Jeep Dodge Ram Bountiful at 3854855488 today or schedule your check engine light service online today! If the engine light comes on due to a serious concern, you risk damaging your vehicle further by not repairing the issue right away. When your check engine light comes on, you should get it checked out swiftly by a adept certified Dodge mechanic.

Dodge Check Engine Light Flashing

Although there are countless potential causes of an illuminated Check Engine Light, we know from years of providing Check Engine Light Diagnosis Service that there are many common causes including something as simple as a loose gas cap. Other mostly common reasons for a Check Engine Light are faulty emissions control part, dirty mass airflow sensor, broken head gasket, damaged oxygen sensor, a malfunction with the fuel injection system, or defective spark plugs to name a few. No matter what is the root cause of the Check Engine Light, we have the Dodge Certified Mechanics and the certified service protocol to isolate the root problem and entirely repair it as needed to restore factory specifications. When this happens, the Check Engine Light turns off, and you can leave the service center knowing that your Dodge issue was entirely fixed.

Every Dodge was designed with a high-technology performance monitoring system with a computer, and a series of sensors positioned strategically throughout the car on its crucial systems. The quick sensors are continually detecting conditions while sending crucial data to the electronic control unit. If the electronic control unit detects that the data is out of factory specifications, the Check Engine Light illuminates telling you that there is a problem. However, unfortunately that is the limitation of the Check Engine Light – it won’t tell you what definitely is wrong nor what to do about it. That’s where we come in; Larry H. Miller Chrysler Jeep Dodge Ram Bountiful provides a Check Engine Light Diagnosis Service that isolates the core problem and gives you a recommendation on what to do next from a Extremely Qualified Service professional.

Check Engine Light Service Dodge

What do you do when you’re driving along in your Dodge and suddenly, a yellow light illuminates on your dash and says "Check Engine". If you’re like most Dodge owners, your heart sinks drastically because you may have definitely idea about what that light is trying to tell you or how you should react. The fear of the unknown (or the cost of the unknown) can be just as stressful. But take a deep, peaceful breath and realize the light coming on doesn’t mean you have to pull the car over to the side of the road and call a tow truck, but it is advised that you get your Dodge checked instantly. Ignoring that warning could end up causing major, major damage to pricey engine components.

When your Dodge 's ECM (electronic control module), which is the vehicle's onboard computer, finds a problem in the electronic control system that it can’t correct, a computer turns on your check engine light. This amber or yellow light is usually labeled “check engine” or “service engine soon”, or the light may be nothing more than a picture of an engine, or a picture of the engine with the word “check.”

When the light turns on, the ECM stores an engine code or “trouble code” in its memory that can rapidly identify the issue, whether it's a sensor or a failing engine part. This code is read with an electronic scan tool that is used by our Dodge auto repair mechanics at Larry H. Miller Chrysler Jeep Dodge Ram Bountiful. There are also a number of relatively inexpensive code readers that are designed for do-it-yourselfers, should you select that route too. While this code will tell you the issue that is detected, a true diagnosis still requires an experienced professional to determine the specifically correct issue and repair it.

Will the check engine light reset itself?

The check engine light on your Dodge will frequently shut itself off if the issue or code that caused it to turn on is fixed. For example, if the cause of your check engine light coming on was a loose gas cap, if it's tightened, the light will promptly turn itself off. Also, if your catalytic converter is working perfectly, and you did a lot of stop-and-go driving, that may have turned on the check engine light due to the high usage of the converter. In most cases, your Dodge light will go off after about 20-40 miles. If you drive over that amount and the light is still on, you will need to bring it in to Larry H. Miller Chrysler Jeep Dodge Ram Bountiful so the light and code can be double-checked and reset.

How much does it cost to get the engine light checked?

The check engine light warns of issues ranging from a gas cap that's not properly tightened to a more serious failure like a bad catalytic converter or a problem with one of the car's oxygen sensors, so it good to get the proper code reading and diagnosis. The average cost for a check engine light diagnosis & testing is typically between $88 and $111. The good news, Larry H. Miller Chrysler Jeep Dodge Ram Bountiful offers entirely complimentary multi-point inspections and free diagnostics, in most cases, to help determine the cause of your check engine light.

Is it safe to drive your Dodge with the check engine light on?

This question is not tremendously simple because it all depends on the severity of the issue. If the cause is a minor issue, such as a loose gas cap, it should be safe to drive. This is generally indicated by a steady glow of the check engine light. If you notice a difference in the performance of the vehicle, it could be an indication of a more serious problem. If the check engine light is flashing, this means that there is a serious issue and it is suggested to service your Dodge immediately. Call the experts at Larry H. Miller Chrysler Jeep Dodge Ram Bountiful by dialing 3854855488 so you can describe the issues. Or reduce your speed and bring your Dodge to our certified mechanics as in the near future as conceivable.

How many miles can you drive with the check engine light?

It could be anything from a bad sensor to plug wires needing to be replaced. If you check engine light is flashing, we advocate that you pull over and contact Larry H. Miller Chrysler Jeep Dodge Ram Bountiful to help determine if your car is safe to drive in or if we advocate a tow truck. Since each check engine code has its own level of severity, it is usually difficult to predict how many miles you can be safe in driving with the warning light on. The safest bet is to decipher the code and then plan your strategy accordingly.